|
|
High Pressure Cleaning Button Nose Nozzles
THRUSTER NOZZLE |
 |
Description: The Thruster has a 25 degree angle for maximum pulling power. Use in a plugged line situation or for runs greater than 150 ft.
Pattern: 1 forward jet (optional), 3 to 6 rear jets |
PENETRATOR NOZZLE |
 |
Description: 35 degree Penetrating angle with super pulling power. Use in a plugged line situation or for runs between 100 to 150 ft.
Pattern: 1 forward jet (optional), 3 to 6 rear jets |
FLUSHER NOZZLE |
 |
Description: The Flusher has a 45 degree angle with good pulling power. Use for runs up to 100 ft. A good general purpose cleaning nozzle.
Pattern: 1 forward jet (optional), 6 to 12 rear jets |
SWEEPER NOZZLE |
 |
Description: 55 degree Sweeping angle, pulling similar power as Flusher nozzle, but offers wider angle for sweeping lines clean.
Pattern: 1 forward jet (optional), 6 to 12 rear jets |
CORNER NOZZLE |
 |
Description: 45 degree Flushing angle combined with a 90 degree side jet to assist nozzle through corners, etc.
Pattern: 1 forward jet (optional), 1 side jet @ 90 degrees & 3 to 6 rear jets |
MONSTER NOZZLE |
 |
Description: A dual angle nozzle combining the forces of both thrust and flush for superior pulling and cleaning power.
Pattern: 1 forward (optional), 2 to 3 rear jets @ 45 degrees & 2 to 3 rear jets @ 25 degrees |
|
High Pressure Cleaning Jet Nozzles
RAM |
 |
Description: Use a 35 degree penetrating angle for maximum pulling power or a 45 degree angle for greater flushing . Use in a plugged line situation.
Pattern: 1 forward jet (optional), 3 to 6 rear jets |
OFFSET |
 |
Description: Similar to the RAM pattern, but the 10 degree offset forward angle permits some sidewall cutting action.
Pattern: 1 forward (10 degree) & 3 to 6 rear jets |
DEGREASER /DE-ICER |
 |
Description: A 45 degree angle is the default choice for this pattern. However, when faced with a longer run a 35 degree angle will provide extra pulling power.
Pattern: 3 forward jets @ 10 degrees, 6 to 12 rear jets @ 45 degreesor 35 degrees |
CUSTOM PATTERNS |
 |
Description: Custom drilling service allows you to specify any type of special or custom pattern utilizing the range of angles shown to the left.
Pattern: Available in 0, 10, 45, 90, 60, 45 and 35 degree patterns shown to the left. |
|
High Pressure Cleaning Rotary Jet Nozzles
STANDARD ROTOR JET PATTERN |
 |
Description: Maximum cleaning action from 90 degree side jets with 45 degree flushing / pulling angle. This pattern is standard for Sewer Squad Kits.
Pattern: 2 side jets @ 90 degrees & 2 rear jets @ 45 degrees |
MAXIMUM FLUSHING / PULLING PATTERN |
 |
Description: The 45degree flushing angle provides the maximum amount of flushing action. This pattern is also used on smaller pumps with lower flows to maximize pulling power for long runs.
Pattern: 2 rear jets @ 45 degrees |
|
High Pressure Cleaning Radial Nose Nozzles
THRUSTER NOZZLE |
 |
Description: 20 degree thrust angle for maximum pulling power. Use in a plugged line situation or to utilize the maximum run capability of your system.
Pattern: 1 forward (optional), 6 to 8 rear jets
|
PENETRATOR NOZZLE |
 |
Description: 30 degree Penetrating angle with very strong pulling power. Use in a plugged line situation on medium to medium long runs.
Pattern: 1 forward (optional), 6 to 8 rear jets
|
MONSTER NOZZLE |
 |
Description: A general purpose dual angle nozzle combining
the forces of both thrust and flush for superior pulling and
cleaning power.
Pattern: 1 forward (optional), 3 to 4 rear jets @ 45 degrees & 3 to 4 rear jets @ 20 degrees
|
|
Contact us
Email: sales@munisupply.com
or Toll Free at
(800) 523-6696
|
